CRM Mitchell1, Author at JR Automotive

2014 GMC Terrain
Mileage
110,567
Service Date
7/23/2024
Services Performed
Inspect unit and verify intoxalock unit works properly ( non start with out blowing). Get millage from the vehicle. Remove hand held unit and start recalibration on station. Install hand held unit to the vehicle and verify unit works accordingly.
Tina W. gave our service a 5 star review on 7/24/2024
2015 Chevrolet Cruze
Mileage
85,200
Service Date
7/10/2024
Services Performed
Multipoint inspection/ see costumer notes. According to costumer one of the key will trigger error message on display and vehicle will not start.
SPARK PLUGS – Remove & Replace – 1.4L Eng,Turbocharger
ALTERNATOR DRIVE BELT – Remove & Replace – 1.4L Eng,Turbocharger – [Includes: R&I Engine Mount. Includes: R&I Fender Liner.] – [Includes: Serpentine and V-Belt type Belt(s).]
Smog Certification
Bryce E. gave our service a 5 star review on 7/16/2024
2010 Toyota FJ Cruiser
Mileage
87,143
Service Date
7/3/2024
Services Performed
Replace Engine Oil and Oil Filter Perform Battery Load Test and Inspect Condition Install Windshield Washer Solvent Check and Adjust Tire Pressure Lube Chassis Where Applicable Inspect All Exterior Lights Inspect Tires For Wear Inspect Drive Belt Inspect Brake Components & Linings For Wear/Damage Check All Serviceable Fluid Levels & Condition Perform Multi-Point Inspection
Recalibrate vehicle compass
Customer states instrument cluster lights intermittent and sometime gauges are too. Inspect and report
Perform road test and rack vehicle. Raise vehicle and remove front wheels. Remove front wheels. Remove calipers from spindle assemblies and remove old brake pads. Remove brake rotors from brake rotors from hub assemblies. Install new rotors onto hub assemblies, clean and lubricate caliper pivot and mounting points, install new brake pads into calipers. Install calipers on spindle and torque calipers bolts to manufactures specifications. Install wheel assemblies torque lug nuts to manufacturers specifications. Road test to verify brake performance and to seat in new pads.
AIR CLEANER ELEMENT – Remove & Replace
Mount and balance tire
ALTERNATOR DRIVE BELT – Remove & Replace – [Includes: Serpentine and V-Belt type Belt(s).]
Bill M. gave our service a 5 star review on 7/3/2024
2017 Nissan Sentra
Mileage
116,506
Service Date
6/28/2024
Services Performed
UBER Inspection
Linda J. gave our service a 5 star review on 6/29/2024
2017 Volkswagen Golf
Mileage
56,243
Service Date
6/21/2024
Services Performed
Found foreign object in between caliper and backing plate. cleared out object and road tested, no further noise found.
Eliza B. gave our service a 5 star review on 6/22/2024
2006 Chrysler PT Cruiser
Mileage
49,116
Service Date
6/11/2024
Services Performed
Perform visual inspection on A/C components, check condenser for any foreign object damage, inspect compressor belt condition. Inspect and adjust A/C compressor belt tension where applicable. Clean A/C condenser fins of dirt and debris. Perform environmentally safe evacuation of A/C system, which removes old freon, oil and any other contaminants such as water. Vacuum test system; this will determine if there is any leaks. Very small leaks may not be detected by unit due to being gradual, so we will add die to system if needed to facilitate the finding in a future service. VACUUM TEST: PASSED NO major leaks detected Recharge system if vacuum test passes; this includes the manufacturer specified amount of freon and compressor oil. Check for proper operation of HVAC controls, blower motor and secondary or primary engine cooling fan. When testing for system function, A/C not cooling as cold as it should. performed further inspection and found radiator cooling fan not coming on. performed diagnostic on cooling fan and tech determined cooling fan inop (Shorted to ground). Recommend to replace radiator cooling fan assembly. Customer declined at this time.
Valter S. gave our service a 5 star review on 6/12/2024
2019 Chevrolet Trax
Mileage
97,826
Service Date
6/6/2024
Services Performed
Verified customer concern, check engine light is illuminated. Perform diagnostic, scanned for all DTC's and found the following codes: P0496:00 Evaporative Emission System Flow During Non-Purge. Tech performed EVAP function test, function test passed. Smoked tested system and found purge solenoid not restricting flow during non-purge, recommend to replace EVAP purge solenoid.
EVAPORATIVE CANISTER PURGE SOLENOID – Remove & Replace
Elizabeth F. gave our service a 5 star review on 6/9/2024
2011 Hyundai Accent
Mileage
131,521
Service Date
6/3/2024
Services Performed
Faulty Neutral Safety Switch
NEUTRAL SAFETY SWITCH – Remove & Replace – Automatic Trans
Stephen G. gave our service a 5 star review on 6/6/2024
2004 Nissan Maxima
Mileage
64,906
Service Date
5/29/2024
Services Performed
Customer states possible suspension damage. Inspect and report
WHEEL STUD – Remove & Replace – Rear,One Side,Rotor
Perform road test and rack vehicle. Raise vehicle and remove Rear wheels. Remove rear wheels. Remove calipers from spindle assemblies and remove old brake pads. Remove brake rotors from brake rotors from hub assemblies. Install new rotors onto hub assemblies, clean and lubricate caliper pivot and mounting points, install new brake pads into calipers. Install calipers on spindle and torque calipers bolts to manufactures specifications. Install wheel assemblies torque lug nuts to manufacturers specifications. Road test to verify brake performance and to seat in new pads.
Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. Check caster and camber angles and adjust as required. If Camber and/ or Caster are not within Spec and adjustment can not be perform because of special equipment prepare estimate, do advise costumer.Set Front toe. Remove alignment equipment. Road test Vehicle.
John L. gave our service a 5 star review on 5/30/2024
2008 Toyota FJ Cruiser
Mileage
145,199
Service Date
4/26/2024
Services Performed
SHOCK &/OR STRUT ASSEMBLY FRONT – Remove & Install or Remove & Replace – Both – [DOES NOT include disassemble or alignment.]
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [Includes: Bleed Brake System (where applicable). DOES NOT include disassemble or alignment (where applicable).]
STABILIZER BAR CONTROL LINK – Remove & Replace – Both
LATERAL ROD – Remove & Replace
Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. Check caster and camber angles and adjust as required. If Camber and/ or Caster are not within Spec and adjustment can not be perform because of special equipment prepare estimate, do advise costumer.Set Front toe. Remove alignment equipment. Road test Vehicle.
Kevin B. gave our service a 5 star review on 4/27/2024

CRM Mitchell1

We Service and Repair all CRM Mitchell1 cars